|
Make a TwistedRibbon
(with AVBros Page Curl)
©Charlieonline
graphics
2002-2012
TutorialsPSP
Please read my
TOU'
Go to The
Tutorial Make
Ballon
Tutorial written by ©charlieonline
graphics
Any
resemblance to any other
tutorial is purely
coincidental.
Please
feel free to link to
this tutorial,
and/or print it out for
your own personal use,
but do not copy it in
any way to put on-line,
pass out,
or re-write or translate it without
permission.
Besides you
may not
script it and sell the script.
You may not sell works
from my Presets or
Tutorials
All my works are
for personal use,
and with no
profit-websites
A link to this site's
required!
Thank you!
This tutorial was
written using PSP9
but
may be done with other
versions,
and assumes
you have a good working
knowledge of PSP and its
tools.
Supplies
needed:
My
Ribbon ==> HERE (or other of your choise)
My AVBros Presets ==>
HERE
(You have to load ch-ribbon9.avcps and ch-ribbon11.avcps)
Plugins:
AVBros Page Curl
Other Ribbon
HERE
Other Ballon
HERE
Settings
Extract
and save the AVBros
Presets to
your Plugins/AvBros
PageCurl folder.
Extract
and open
the Ribbon and
minimize it to your Psp workspace.
You can use the
arrow to help
you as a mark to
do the
tutorial.
If you like to print it click
below:
Let's begin!!
Open the
ribbon
Duplicate
it and close the original
You see it
sizes 1245x48 px
Go to
Image - Canvas size and change to 2500 x 2500
Duplicate
twice
Rename
the 2nd duplicated ribbon as ribbon first
Layers -
Arrange - Move Down
and close
it
Make the
original layer active and place it at the left side
Now make
the 1st duplicated ribbon active
and place
it at the right of the original one,
so you
have a large ribbon from the left side to right.
Layers - Merge Down
Rename
this one : second ribbon
Enclose
the first ribbon
and apply
a slight drop shadows:
Effects 3D
- Drop Shadow as follow:
click
Ok
Repeat but
change Vertical to -1
Apply the same shadow to the second ribbon
Make the
first ribbon layer active
Effects -
Plugins - AV Bros Page Curl
Click to Main - Load Settings (Relative)
Go to the
folder you saved my Presets
and get the ch-ribbon11.avcps
Click Apply
Make the
second ribbon layer active
Effects -
Plugins - AV Bros Page Curl
Click to Main - Load Settings (Relative)
Go to the
folder you saved my Presets
and this time choose the ch-ribbon9.avcps
Click Apply
Place it on the top of
the ribbon first as the screen bellow
On the Layers Palette,
low the Opacity to 54
as you can see the ribbon
on the bottom
Open the Freehand
Selection Tool, with these settings
Selection type = Point to point
- Mode = Replace - Feather = 0,
Smoothing = 0 - Anti-alias = ticked
Draw a selection as shown in the screen bellow
Make sure you have to
activate the ribbon first
Press the delete key
Selections
- Select none
Then draw a selection as shown in the screen bellow
Make sure you have to
activate the ribbon second
Press the delete key
Selections
- Select none
Raise the Opacity to 100
again,
and make sure the second
ribbon is well placed on the first one
take as a model the
finished work
If you like apply a
colorize:
Adjust
- Hue and Saturation -
Colorize
When you are satisfied on
it,
and the 2 pieces are
in the right position
(as the finished image)
Layers - Merge Visible
and save as a .pspimage
Here my result:
If you like, you can use
this ribbon to bind a ballon as you see at the top.
Done!
Hope you have enjoyed
this tutorial.
If
you have any questions,
please write a message
in to my
Contatti
And if you like it, please leave a message on my
TagBoard
Written on March 2009
TutorialsPSP
©charlieonline graphics 2002-2012
| 
